- INTRODUCTION TO ATM NETWORK
ATM Cell Format
ATM Devices
ATM Network Interfaces
ATM Services
ATM Virtual Connections
ATM Reference Model
The ATM Physical Layer
Types Of ATM Adaptation Layers
ATM Quality of Service
ATM Signaling and Connection Establishment
PNNI(Private network-network interface)
TABLE OF CONTENTS
| ...... ATM NETWORK ......... | ... COMPUTER NETWORK.. |
| DATA COMMUNICATION | ..... NETWORK MANAGEMENT |
| ..NETWORK SECURITY | |
.. ISDN |
SQL/DBMS |
| MORE TO COME... |
INDEX OF ATM NETWORK
Labels: ATM NETWORK
PNNI(Private network-network interface)
PNNI provides two significant services: When a station sends a call setup request to its local switch, the ingress switch references the PNNI routing table to determine a path between the source and the intended destination that meets the QoS requirements specified by the source. The switch attached to the source then builds a list defining each switch hop to support the circuit to the destination. This is called the designated transit list (DTL). VCI = 18 is reserved for PNNI.
ATM topology discovery and call establishment. For switches to build connections between end points, the switch must know the ATM network topology. PNNI is the ATM routing protocol that enables switches to automatically discover the topology and the characteristics of the links interconnecting the switches. A link-state protocol much like OSPF, PNNI tracks things such as bandwidth on links. When a significant event occurs that changes the characteristics of a link, PNNI announces the change to the other switches.
Labels: ATM NETWORK
ATM Signaling and Connection Establishment
The ATM Connection-Establishment Process
ATM signaling uses the one-pass method of connection setup that is used in all modern telecommunication networks, such as the telephone network. An ATM connection setup proceeds in the following manner. First, the source end system sends a connection-signaling request. The connection request is propagated through the network. As a result, connections are set up through the network. The connection request reaches the final destination, which either accepts or rejects the connection request.
Routing of the connection request is governed by an ATM routing protocol (Private Network-Network Interface [PNNI], which routes connections based on destination and source addresses), traffic, and the QoS parameters requested by the source end system. Negotiating a connection request that is rejected by the destination is limited because call routing is based on parameters of initial connection; changing parameters might affect the connection routing. Figure the one-pass method of ATM con Connection-Request Routing and Negotiation
nection establishment.
Labels: ATM NETWORK
ATM Quality of Service
A traffic contract specifies an envelope that describes the intended data flow. This envelope specifies values for peak bandwidth, average sustained bandwidth, and burst size, among others. When an ATM end system connects to an ATM network, it enters a contract with the network, based on QoS parameters.
Traffic shaping is the use of queues to constrain data bursts, limit peak data rate, and smooth jitters so that traffic will fit within the promised envelope. ATM devices are responsible for adhering to the contract by means of traffic shaping. ATM switches can use traffic policing to enforce the contract. The switch can measure the actual traffic flow and compare it against the agreed-upon traffic envelope. If the switch finds that traffic is outside of the agreed-upon parameters, it can set the cell-loss priority (CLP) bit of the offending cells. Setting the CLP bit makes the cell discard eligible, which means that any switch handling the cell is allowed to drop the cell during periods of congestion.
Labels: ATM NETWORK
Types Of ATM Adaptation Layers
*AAL2
*AAL3/4
*AAL5
ATM Adaptation Layers: AAL1
AAL1, a connection-oriented service, is suitable for handling constant bit rate sources (CBR), such as voice and videoconferencing. ATM transports CBR traffic using circuit-emulation services.AAL1 requires timing synchronization between the source and the destination. For this reason, AAL1 depends on a medium, such as SONET, that supports clocking.
The AAL1 process prepares a cell for transmission in three steps.
First, synchronous samples (for example, 1 byte of data at a sampling rate of 125 microseconds) are inserted into the Payload field.
Second, Sequence Number (SN) and Sequence Number Protection (SNP) fields are added to provide information that the receiving AAL1 uses to verify that it has received cells in the correct order.
Third, the remainder of the Payload field is filled with enough single bytes to equal 48 bytes.
Figure illustrates how AAL1 prepares a cell for transmission.

ATM Adaptation Layers: AAL2
AAL2 is suitable for VBR traffic. The AAL2 process uses 44 bytes of the cell payload for user data and reserves 4 bytes of the payload to support the AAL2 processes.
VBR traffic is characterized as either real-time (VBR-RT) or as non-real-time (VBR-NRT). AAL2 supports both types of VBR traffic.
ATM Adaptation Layers: AAL3/4
AAL3/4 supports both connection-oriented and connectionless data. It was designed for network service providers and is closely aligned with Switched Multimegabit Data Service (SMDS). AAL3/4 is used to transmit SMDS packets over an ATM network.
AAL3/4 prepares a cell for transmission in four steps.
First, the convergence sublayer (CS) creates a protocol data unit (PDU) by prepending a beginning/end tag header to the frame and appending a length field as a trailer.
Second, the segmentation and reassembly (SAR) sublayer fragments the PDU and prepends a header to it.
Third the SAR sublayer appends a CRC-10 trailer to each PDU fragment for error control.
Fourth, the completed SAR PDU becomes the Payload field of an ATM cell to which the ATM layer prepends the standard ATM header.
An AAL 3/4 SAR PDU header consists of Type, Sequence Number, and Multiplexing Identifier fields. Type fields identify whether a cell is the beginning, continuation, or end of a message. Sequence number fields identify the order in which cells should be reassembled. The Multiplexing Identifier field determines which cells from different traffic sources are interleaved on the same virtual circuit connection (VCC) so that the correct cells are reassembled at the destination.
ATM Adaptation Layers: AAL5
AAL5 is the primary AAL for data and supports both connection-oriented and connectionless data. It is used to transfer most non-SMDS data, such as classical IP over ATM and LAN Emulation (LANE). AAL5 also is known as the simple and efficient adaptation layer (SEAL) because the SAR sublayer simply accepts the CS-PDU and segments it into 48-octet SAR-PDUs without reserving any bytes in each cell.
AAL5 prepares a cell for transmission in three steps.
First, the CS sublayer appends a variable-length pad and an 8-byte trailer to a frame. The pad ensures that the resulting PDU falls on the 48-byte boundary of an ATM cell. The trailer includes the length of the frame and a 32-bit cyclic redundancy check (CRC) computed across the entire PDU. This allows the AAL5 receiving process to detect bit errors, lost cells, or cells that are out of sequence.
Second, the SAR sublayer segments the CS-PDU into 48-byte blocks. A header and trailer are not added (as is in AAL3/4), so messages cannot be interleaved.
Finally, the ATM layer places each block into the Payload field of an ATM cell. For all cells except the last, a bit in the Payload Type (PT) field is set to 0 to indicate that the cell is not the last cell in a series that represents a single frame. For the last cell, the bit in the PT field is set to 1. Read More......
Labels: ATM NETWORK
The ATM Physical Layer
1.Cells are converted into a bitstream
2.The transmission and receipt of bits on the physical medium are controlled
3.ATM cell boundaries are tracked
4.cells are packaged into the appropriate types of frames for the physical medium.
The ATM physical layer is divided into two parts:
1.The physical medium-dependent (PMD) sublayer
2.the transmission convergence (TC) sublayer.
The PMD sublayer provides two key functions.
First, it synchronizes transmission and reception by sending and receiving a continuous flow of bits with associated timing information.
Second, it specifies the physical media for the physical medium used, including connector types and cable.
The TC sublayer has four functions:
1.cell delineation
2.header error control (HEC) sequence generation and verification,
3.cell-rate decoupling
4.transmission frame adaptation.
The cell delineation function maintains ATM cell boundaries, allowing devices to locate cells within a stream of bits. HEC sequence generation and verification generates and checks the header error control code to ensure valid data. Cell-rate decoupling maintains synchronization and inserts or suppresses idle (unassigned) ATM cells to adapt the rate of valid ATM cells to the payload capacity of the transmission system. Transmission frame adaptation packages ATM cells into frames acceptable to the particular physical layer implementation.
Labels: ATM NETWORK
ATM Reference Model
The ATM reference model is composed of the following planes, which span all layers:
•Control—This plane is responsible for generating and managing signaling requests.
•User—This plane is responsible for managing the transfer of data.
•Management—This plane contains two components:
–Layer management manages layer-specific functions, such as the detection of failures and protocol problems.
–Plane management manages and coordinates functions related to the complete system.
The ATM reference model is composed of the following ATM layers:

•Physical layer—Analogous to the physical layer of the OSI reference model, the ATM physical layer manages the medium-dependent transmission.
•ATM layer—Combined with the ATM adaptation layer, the ATM layer is roughly analogous to the data link layer of the OSI reference model. The ATM layer is responsible for the simultaneous sharing of virtual circuits over a physical link (cell multiplexing) and passing cells through the ATM network (cell relay). To do this, it uses the VPI and VCI information in the header of each ATM cell.
•ATM adaptation layer (AAL)—Combined with the ATM layer, the AAL is roughly analogous to the data link layer of the OSI model. The AAL is responsible for isolating higher-layer protocols from the details of the ATM processes. The adaptation layer prepares user data for conversion into cells and segments the data into 48-byte cell payloads.
Finally, the higher layers residing above the AAL accept user data, arrange it into packets, and hand it to the AAL. Figure illustrates the ATM reference model.
Labels: ATM NETWORK
ATM Virtual Connections
ATM networks are fundamentally connection-oriented, which means that a virtual channel (VC) must be set up across the ATM network prior to any data transfer. (A virtual channel is roughly equivalent to a virtual circuit.)
Two types of ATM connections exist: virtual paths, which are identified by virtual path identifiers, and virtual channels, which are identified by the combination of a VPI and a virtual channel identifier (VCI).
A virtual path is a bundle of virtual channels, all of which are switched transparently across the ATM network based on the common VPI. All VPIs and VCIs, however, have only local significance across a particular link and are remapped, as appropriate, at each switch.
A transmission path is the physical media that transports virtual channels and virtual paths. Figure illustrates how VCs concatenate to create VPs, which, in turn, traverse the media or transmission path.
ATM Switching Operations
The basic operation of an ATM switch is straightforward:
The cell is received across a link on a known VCI or VPI value. The switch looks up the connection value in a local translation table to determine the outgoing port (or ports) of the connection and the new VPI/VCI value of the connection on that link. The switch then retransmits the cell on that outgoing link with the appropriate connection identifiers. Because all VCIs and VPIs have only local significance across a particular link, these values are remapped, as necessary, at each switch.
Labels: ATM NETWORK
ATM Services
Three types of ATM services exist:
1.permanent virtual circuits (PVC)
2.switched virtual circuits (SVC)
3.connectionless service (which is similar to SMDS).
PVC allows direct connectivity between sites. In this way, a PVC is similar to a leased line. Among its advantages, PVC guarantees availability of a connection and does not require call setup procedures between switches. Disadvantages of PVCs include static connectivity and manual setup. Each piece of equipment between the source and the destination must be manually provisioned for the PVC. Furthermore, no network resiliency is available with PVC.
An SVC is created and released dynamically and remains in use only as long as data is being transferred. In this sense, it is similar to a telephone call. Dynamic call control requires a signaling protocol between the ATM endpoint and the ATM switch. The advantages of SVCs include connection flexibility and call setup that can be handled automatically by a networking device. Disadvantages include the extra time and overhead required to set up the connection.
Labels: ATM NETWORK
ATM Network Interfaces
An ATM network consists of a set of ATM switches interconnected by point-to-point ATM links or interfaces. ATM switches support two primary types of interfaces: UNI and NNI. The UNI connects ATM end systems (such as hosts and routers) to an ATM switch. The NNI connects two ATM switches.
Depending on whether the switch is owned and located at the customer's premises or is publicly owned and operated by the telephone company, UNI and NNI can be further subdivided into public and private UNIs and NNIs. A private UNI connects an ATM endpoint and a private ATM switch. Its public counterpart connects an ATM endpoint or private switch to a public switch. A private NNI connects two ATM switches within the same private organization. A public one connects two ATM switches within the same public organization.
An additional specification, the broadband intercarrier interface (B-ICI), connects two public switches from different service providers. Figure the ATM interface specifications for private and public networks.
Labels: ATM NETWORK
ATM Devices
An ATM network is made up of an ATM switch and ATM endpoints. An ATM switch is responsible for cell transit through an ATM network. The job of an ATM switch is well defined: It accepts the incoming cell from an ATM endpoint or another ATM switch. It then reads and updates the cell header information and quickly switches the cell to an output interface toward its destination. An ATM endpoint (or end system) contains an ATM network interface adapter. Examples of ATM endpoints are workstations, routers, digital service units (DSUs), LAN switches, and video coder-decoders (CODECs). Figure illustrates an ATM network made up of ATM switches and ATM endpoints.
Labels: ATM NETWORK
ATM Cell Format
Figure illustrates the basic format of an ATM cell.
ATM Cell Header Format
An ATM cell header can be one of two formats: UNI or NNI. The UNI header is used for communication between ATM endpoints and ATM switches in private ATM networks. The NNI header is used for communication between ATM switches. Figure 27-5 depicts the basic ATM cell format, the ATM UNI cell header format, and the ATM NNI cell header format.

Unlike the UNI, the NNI header does not include the Generic Flow Control (GFC) field. Additionally, the NNI header has a Virtual Path Identifier (VPI) field that occupies the first 12 bits, allowing for larger trunks between public ATM switches.
ATM Cell Header Fields
In addition to GFC and VPI header fields, several others are used in ATM cell header fields. The following descriptions summarize the ATM cell header fields illustrated in Figure:
•Generic Flow Control (GFC)—Provides local functions, such as identifying multiple stations that share a single ATM interface. This field is typically not used and is set to its default value of 0 (binary 0000).
•Virtual Path Identifier (VPI)—In conjunction with the VCI, identifies the next destination of a cell as it passes through a series of ATM switches on the way to its destination.
•Virtual Channel Identifier (VCI)—In conjunction with the VPI, identifies the next destination of a cell as it passes through a series of ATM switches on the way to its destination.
•Payload Type (PT)—Indicates in the first bit whether the cell contains user data or control data. If the cell contains user data, the bit is set to 0. If it contains control data, it is set to 1. The second bit indicates congestion (0 = no congestion, 1 = congestion), and the third bit indicates whether the cell is the last in a series of cells that represent a single AAL5 frame (1 = last cell for the frame).
•Cell Loss Priority (CLP)—Indicates whether the cell should be discarded if it encounters extreme congestion as it moves through the network. If the CLP bit equals 1, the cell should be discarded in preference to cells with the CLP bit equal to 0.
•Header Error Control (HEC)—Calculates checksum only on the first 4 bytes of the header. HEC can correct a single bit error in these bytes, thereby preserving the cell rather than discarding it.
Labels: ATM NETWORK
INTRODUCTION TO ATM NETWORK
ATM is based on the efforts of the ITU-T Broadband Integrated Services Digital Network (B-ISDN) standard. It was originally conceived as a high-speed transfer technology for voice, video, and data over public networks.
ATM Devices and the Network Environment
ATM is a cell-switching and multiplexing technology that combines the benefits of circuit switching (guaranteed capacity and constant transmission delay) with those of packet switching (flexibility and efficiency for intermittent traffic). It provides scalable bandwidth from a few megabits per second (Mbps) to many gigabits per second (Gbps). Because of its asynchronous nature, ATM is more efficient than synchronous technologies, such as time-division multiplexing (TDM).
With TDM, each user is assigned to a time slot, and no other station can send in that time slot. If a station has much data to send, it can send only when its time slot comes up, even if all other time slots are empty. However, if a station has nothing to transmit when its time slot comes up, the time slot is sent empty and is wasted. Because ATM is asynchronous, time slots are available on demand with information identifying the source of the transmission contained in the header of
each cell.
Figure illustrates a private ATM network and a public ATM network carrying voice, video, and data traffic.

Labels: ATM NETWORK
disable right
Labels
- ATM NETWORK (13)
- C (44)
- COMPUTER NETWORK (38)
- DATA COMMUNICATION (24)
- DBMS/SQL (30)
- DOWNLOAD E BOOKS (1)
- HTML (1)
- ISDN (4)
- NETWORK MANAGEMENT (27)
- NETWORK SECURITY (11)
- UML (6)
- WEB ENGG. (17)
About Me
- prince kumar
- bhopal, M.P., India
